From concept through to design, the Kinematics, the geometry and specification; the Reactor is designed from the ground up to be the ultimate aggressive trail bike. It is at home on technical climbs, but happiest when thrashing the most technical trails you can point it at.
To optimise the weight, strength and stiffness, the Reactor Carbon frame features a full UD woven carbon fibre frameset (Including chain and seat stays). It is available for 27.5” or 29” wheel sizes. These are two totally different, compromise-free frames that were designed and developed at the same time. Each frame is simply tailored around each wheel size.
Speed or play: which do you value more? The manoeuvrability of 27.5” or the raw speed of a 29”?
All Reactor frames feature a “flip-chip” to adjust the geometry from “Trail” to “Rail mode”.
Trail – As the name suggests, this setting is best suited for trail riding. It is for riders who get as much enjoyment from the climb as the descents.
Rail - The Rail setting turns the Reactor into a corner shredder, dropping the bottom bracket 6mm and slackening the head angle by half a degree. It is there to maximise descending capabilities.
To ensure the bike could climb as well as it descends, we designed the 4 bar horst linkage to have higher levels of anti-squat for climbing gears but lower levels when you drop down the cassette. This means that the bike can behave itself on the climbs but when you get it up to speed, it turns into a trail hooligan. The combination of low anti-squat and progressive rate give ultimate small bump compliance (removes rough trail and root chatter) with good mid-stroke support for cornering/pumping and end stroke progression for aggressive riding. Balanced anti-rise figures allow the Reactor some squat when braking hard, maintaining rider position and providing a good amount of pressure through the tyre to ensure traction. The Reactor is designed to reward the rider and ensure you get that stoke factor in on any ride.
Frame: Nukeproof Reactor 275 Carbon, 140mm Travel, UD woven Carbon Fibre frame
internal cable routing
Threaded 73mm BB
Boost 148mm rear axle spacing
3D contoured Rubber frame protection
2 position adjustable Flip chip system
Shock: Fox Float DPX2, Factory Series, Kashima, 3 Position, EVOL LV, Custom CL, DRL, Rezi A F F tune, 210x55mm, Bearing End, 1x 0.3 spacer fitted. (SHORT ID: D6TD)
Headset: Nukeproof, 44-56 IITS
Weight: 3.6Kgs/7.9lbs (Medium)
Material: Ultra Strong T700/800 Monocoque Carbon Fibre
Fork Travel: 150mm (RS 160mm)
Axle to Crown: 545mm (RS 555mm)
Fork Offset: 46mm
Rear Travel: 140mm
Wheels Size: 27.5"
Max Tyre Size: 2.6"
Recommended Shock Sag (Measured seated): 30% (16.5mm)
Shock Size: 210x55mm
Shock Hardware F: 25x8mm
Shock Hardware R: 30x8mm
Headtube: 44-56mm Tapered Semi-Integrated
Headset: ZS44-28.6 - T2 / ZS56/40 - B8
Bearings Required: 2x (6902 2RS), 4x (6800 2RS), 4x (6901 2RS)
Seatpost: 31.6mm (Internal Routing for Dropper Seatpost)
Seat Clamp: 36.4mm
BB: Threaded 73mm BSA
Rear Hub: Boost 148x12mm
Rear Axle: Sram Maxle Stealth M12x1.75 180mm (Thread Length 20mm)
Chain Guide: ISCG05
Brake Mount: 180mm Direct Post
Protection: 3D Contoured Rubber Frame Protection for DT/SS/CS
|身高/ 高度||cm||155 - 170cm||170 - 180cm||180 - 190cm||190 - 200cm|
|ft||5′ 1″ - 5′ 7″||5′ 7″ - 5′ 106⁄7″||5′ 106⁄7″ - 6′ 24⁄5″||6′ 24⁄5″ - 6′ 63⁄4″|
|内侧腿长||cm||71 - 76cm||76 - 81cm||81 - 86cm||86 - 92cm|
|英寸||28″ - 297⁄8″||297⁄8″ - 317⁄8″||317⁄8″ - 336⁄7″||336⁄7″ - 361⁄5″|